Cisco 24-Port T1 E1 J1 Circuit Emulation & ATM SPA

0.75 lbs

Compatible with:
- Cisco ASR 1000 Series Routers (CE mode only)
- Cisco 7600 Series Routers
- Cisco XR 12000 Series Routers

(1) 24-Port Circuit Emulation Over Packet Port Adapter
(1) 100-pin connector

PROTOCOLS:

Circuit Emulation:
- IETF RFC 4553 (SAToP PWE)
- IETF draft-ietf-pwe3-cesopsn-07 (CESoPSN PWE)

ATM:
- IETF RFC 2684 (updated RFC 1483) support for multiple protocol encapsulations over ATM
- IETF RFC 2364 and 2516 for Point-to-Point Protocol (PPP) over ATM
- IETF RFC 1577 support for classical IP and Address Resolution Protocol (ARP) over ATM
- ATM Forum User-Network Interface (UNI) 3.0, 3.1, and 4.0

FEATURES & FUNCTIONS:

Circuit Emulation:
- MPLS encapsulation for CESoPSN and SAToP PWE transport
- 320 ms jitter buffer
- T1/E1 and nxDS0 CEoP PWEs
- Maximum of 24 T1/ E1 or J1 ports or 191 nxDS0 groups
- Jitter and wander compliant to G.823/G.824 traffic interface
- synchronous, differential or adaptive clock recovery modes
- Targets 15ppb or better adaptive clock recovery accuracy
- BITS support
- Configurable clock source

ATM:
- CBR
- VBR-nrt
- VBR-rt
- UBR and UBR+
- Maximum virtual circuits: 2,000 (subject to overall configuration limitations)
- ATM and IP CoS
- Per-virtual circuit and per-virtual path traffic shaping
- Per-virtual circuit and per-virtual path statistics
- PWE3 support
- ATM permanent virtual circuits (PVCs) and switched virtual circuits (SVCs)
- F4 and F5 OAM cell support
- Interim Local Management Interface (ILMI) 1.0
- Layer 2 transport and Layer 3 termination on the same port
- ATM over MPLS
- IMA

TELECOMMUNICATION INTERFACE INDUSTRY STANDARDS (T1):

Data rate to 1.536 Mbps per port:
- Impedance: 100 ohms
- D4 Super Frame (SF) or Extended Super Frame (ESF) framing
- Alternate mark inversion (AMI) or binary 8-zero substitution (B8ZS) line encoding
- ANSI T1.403 and AT&T TR 54016 Facility Data Link (FDL)
- Selectable T1 CSU line build-out (LBO): 0, -7.5, -15, and -22.5 dB
- Selectable T1 CSU receiver gain: 26 or 36 dB
- Alarm monitoring:
- Alarm indication signal (AIS)
- Out of frame (OOF)
- Far-end alarm failure (yellow or distant alarm)
- Performance data collection:
- CRC and bit errors
- Framing bit errors
- Line errored seconds
- Far-end errored seconds
- Far-end severely errored seconds
- Far-end unavailable seconds
- Line coding violation (LCV)
- TIA-968-A (U.S. requirement, formerly known as FCC Part 68)
- G.703
- G.704
- G.824
- CS-03 (Canada)
- T1.403
- GR-499

TELECOMMUNICATION INTERFACE INDUSTRY STANDARDS (E1):

Data rate to 2.048 Mbps (unframed mode) or 1.984 Mbps (framed mode) per port:
- Impedance: 120 ohms (adapter cable offers 75-ohm configuration option)
- Unframed E1, CRC4, or non-CRC4 framing
- High-density bipolar with three zeroes (HDB3) line encoding
- Alarm monitoring:
- AIS
- OOF
- Remote alarm indication (RAI)
- Performance data collection:
- CRC and bit errors
- Framing bit errors
- Far-end block error (FEBE)
- LCV
- G.703
- G.704
- G.706
- G.823
- TBR 4, 12, and 13 (Europe)
- ACA S016 (Australia)

ENVIRONMENTAL PROPERTIES:

Operating Temperature: 41 to 104 F (5 to 40 C)
Storage Temperature: -38 to 150 F (-40 to 70 C)
Operating Humidity: 5 to 85 % relative humidity
Storage Humidity: 5 to 95% relative humidity

0.8"hx 6.8"w x 7.3"d

(24) Channelized T1/E1/J1

20W

Due to manufacturer restrictions, all sales on this item are final.

4.27 lbs

43222612